15ft X 9.5ft Superflex Alpha Systems RV Camper Rubber Roof Kit

15ft X 9.5ft Superflex Alpha Systems RV Camper Rubber Roof Kit
Click To Enlarge
  • Item #: SF-1595-4T2R1G
  • Condition: New
  * Marked fields are required.
Qty*
Price $219.83
Availability In-Stock
# Available 48

Price Includes FedEx Ground Shipping

 

Kit will ship in two boxes and Includes

15 Feet x 9 1/2 Feet SuperFlex Roofing Roll - Folded

4 tubes of Alpha Systems 1021 Self Leveling Sealant (11 oz)

2 Rolls of Putty Tape (1/8" Thick x 3/4" W x 30' L)

1 Gallon of Alpha Systems Rubber Roof Adhesive (8010)



OEM PART

No retail box and no install instructions

Have a certified technician install all parts to prevent product damage and personal injury

 

For information on installation of product

Alpha Installation Video

https://youtu.be/a7NLrfjCUUk

 

JManatee's & Family RVing Site - he removes old rubber roof and installs new

http://www.outerland.com/RV/Roof/



Features & Specifications SuperFlex Roofing Roll

Single-ply membrane that is approximately half of the weight of EPDM

.165 lbs/sq feet compared to EPDM at .29 lbs/sq foot

COLOR: White

Will not chalk, fade, or leave streaks down the side of your RV

Brilliant UV performance and is resistant to mold, algae, and fungus

Better puncture resistance than EPDM at .028 Thick

Non-skid surface for better traction. Install roofing with smooth side down, facing glue.

Color is same throughout substrate

Will not shrink or crack (100% solids sealant)

Stretches easier so you can get a perfect, tight fit

Can be easily repaired.

 

Features & Specifications Alpha Systems 1021 Self Leveling Sealant

1021 HIGH SOLIDS SEALANT is a one part all weather self-leveling sealant designed and formulated to provide excellent weather resistance.

It features high solids, low V.O.C. content, and no hazardous air pollutants (HAP).

This compound provides good adhesion to a variety of substrates.

This product has good low temperature resistance and will not crack at -40oF.

Typically used in RV applications where a long-term weather tight seal with good ozone and UV resistance are required.

Cured sealant is paintable.

Surfaces should be free of dirt, oil, or other contaminants. A solvent cleaned surface is optimum.

BASE: EPDM

SOLVENT:   Heptane

VISCOSITY:  80,000 - 200,000 cps

COVERAGE:  380 lineal ft/gal

COLOR: White

MINIMUM APPLICATION TEMP: 60 deg F

CAUTION:  THIS MATERIAL MAY BE HARMFUL OR FATAL IF SWALLOWED.  IF SWALLOWED, DO NOT INDUCE VOMITING. CALL A PHYSICIAN.  THIS MATERIAL IN THE LIQUID OR VAPOR PHASES IS EXTREMELY FLAMMABLE. KEEP AWAY FROM SPARKS OR OPEN FLAME.  DON'T SMOKE.Prolonged breathing of vapors may cause headaches and even unconsciousness. Avoid prolonged breathing and use good ventilation.

 

Features & Specifications Putty Tape

Non-hardening, pliable putty tape.

COLOR: Gray

Waterproofs overlapping metal seams.

1/8" high X 3/4" wide - Roll 30 feet long

 

Features & Specifications Alpha Systems 8010 Adhesive

8010 is a technically advanced scientific formula of water base adhesive designed for use as a bonding adhesive for single ply roofing membranes.

DESIGNED TO BOND: EPDM, PVC, and Hypalon to wood fiberboard, plywood, EPS, any typical polyisocyanurate insulation, gypsum, concrete, etc.

8010 may be applied by spray, roll coating, or by brush.

Grows stronger and adheres more with age.

Remains flexible to compensate for expansion and contraction of the membrane itself.

COLOR: White

SOLVENT: Water Based

ADHESIVE TYPE: Modified Acrylic

COLOR: White

COVERAGE: 160-200 sq ft/gal (1side @ 8-10 mil)

NET WEIGHT: 8.50 lbs/gal

SOLIDS CONTENT: 68%

VISCOSITY: 10,000-15,000 cps (Brookfield RVF)

8010 may be applied by spray, roll coating, or by brush.

(When using spray application an Aro 650095 4.25 inch air motor with a 30:1 ratio pump @ 80 psi using a 651-500 gun equipped with #651551 quick clean and spray tip #T.C. 1565 with 0.015 orifice or similar equipment is recommended).

For maximum bond strength a two-sided application is recommended.

If one surface is porous, such as plywood or fiberboard, it is acceptable to wet laminate the membrane to the substrate.

If both surfaces are non-porous, such as EPS or ISO apply the adhesive to both surfaces 4 - 5 mils and allow to dry approximately 20 - 30 minutes, depending on conditions.

Adhesive will turn from white to clear when it is dry.

Apply membrane to roof deck and roll or broom down sheet to assure 100% contact area.

DO NOT FREEZE - KEEP OUT OF REACH OF CHILDREN